1 1 - M T S D I S T R I B U T I O N 4.0 - | (Revised for Distribution 4.3) - | May 1980 - General Notes - Note: Installations receiving this distribution of MTS + ____ should obtain approval from the University of Michigan Computing Center before distributing any part of the distribution to any installation other than one of those listed at the end of these notes. - 0 MTS, the Michigan Terminal System, is distributed using two + _ _ _ | types of tapes: (1) dump/restore tapes for a single pack (3330 | mod 1) MTS system designed to be used as the base system (for new installations) or for testing and conversion (for old installations), and (2) tapes generated by the MTS *FS program which contain the source, object, command, data, and print files for the system. The *FS tapes are "volume label only" (VLO) | tapes; they must be mounted using the keyword LBLTYPE=VLO. The | dump/restore tapes sent as part of D4.0, D4.1 and D4.2 were IBM | TSS VAM2 format, while the D4.3 dump/restore tapes are MTS VAMX | format. 0 In addition to the general information contained in this writeup, there are two other writeups which give more specific information about installing MTS, one for new installations and one for old. A hardcopy of the appropriate writeup is included | (item 10068 or 10069); both are available on the *FS tapes. 0 Distribution 4.0 (September 1977) was a complete distribution of the system. Supplemental distributions D4.1, | D4.2, and D4.3 were completed in May 1978, March 1979, and May | 1980, respectively. They differ from D4.0 in that the *FS tapes contain only those components which have been added to the system or changed since the previous distribution. Other components are not included since they may be obtained from the D4.0 *FS tapes. For installations which have not previously received a distribution of MTS, the *FS tapes for D4.0, D4.1, | and D4.2 are included with D4.3. However, the dump/restore | tapes for D4.0, and D4.1 are not included since the D4.3 | dump/restore tapes provide a complete, current system. The D4.2 | dump/restore tapes are included so that the TSS stand-alone | utilities may be used to restore the D4.2 system which may in | turn be used to restore the D4.3 system. This is necessary | because there is currently no stand-alone program to restore a 1 2 - | VAMX pack. 0 Throughout the distribution, reference is made to the components of the distribution. Generally these references consist of a 3- or 4-digit component number, usually followed by a slash and a subcomponent number. For example, the MTS accounting system has been assigned component number 104. However, the accounting system actually has many "pieces" and so it consists of well over 100 subcomponents, beginning with | number 104/1. A component will almost always have the same | number, but subcomponent numbers may be changed. Thus, for | example, something may have been distributed on D4.2 with the | number 104/15, while on D4.3 it may be 104/16 (this could happen | if a subcomponent containing an update were inserted between | source and object). New components numbers are assigned by each MTS installation in ranges. The number of a component doesn't necessarily indicate which installation is responsible for its maintenance (there is a installation code for that), just which installation originally assigned the number. 0 The installation assignment ranges are as follows: 0 Range Code Installation Name 0 0001-0999 UM University of Michigan 1000-1199 UBC University of British Columbia 2000-2199 UNE University of Newcastle upon Tyne 3000-3199 UQV University of Alberta 4000-4199 WSU Wayne State University 4200-4399 RPI Rensselaer Polytechnic Institute 4400-4599 SFU Simon Fraser University 4600-4799 EMB EMBRAPA (Brasilia) | 4800-4999 RIO CNPq/CBPF/GPD (Rio de Janeiro) | 9000-9999 UM Used for redistributions only 0 The *FS tapes are generated by the MTS *FS program based on information contained in a data file (known as a driver file), each line of which describes a component (or subcomponent) of the system. Each component has a name, an optional subcomponent name, a installation code, a type code (source, object, MTS commands, etc.), a location (the file name or tape from which it was obtained), a contact person at the installation principally responsible for its maintenance, a locally responsible person (optional), an optional disk name (which gives the file name, if any, on the dump/restore pack where this component is also | located), and an optional revision level (revision levels "A" | and "C" have been used to mark the subset of the driver file | which is included in D4.3). 0 | Revision level "A" denotes subcomponents which have been | changed in the UM production system since D4.2 (March 1979) | (these may, however, have been included in a redistribution | since D4.2). Subcomponents with revision level "C" are | completely new for D4.3, i.e., they have never been seen by | other installations before, either on a distribution or a | redistribution. 1 3 - The driver file editor program (*DEDIT) may be used to edit and print a driver file. In the distributed driver file, the local persons, when given, are UM people for non-UM components; each other installation should use *DEDIT to fill in its own local names for components assigned to other installations. In this way, a printout may be produced (using the *DEDIT PLIST command) for each programmer, showing the components for which | he or she is responsible. This is also a convenient way to | inform other installations of who is currently responsible for | various components at your installation. 0 As *FS generates the distribution tapes, it adds additional information to each line in the driver file, such as the name of the distribution tape on which it has written the component | (tapes are named D4Tn, D4.1Tn, D4.2Tn, and 4.3Tn), the file number on the distribution tape, a unique name for the component (known as the FS name), information about the file size or tape blocking information if the component was obtained from a regular (non-FS) tape, and the time and date when the file was saved. Components may be obtained from these tapes using the *FS RESTORE command, either by reference to the FS name or to the file number. 0 Two versions of the distribution driver file are provided: 461/5 for the 6250 bpi tapes, and 461/6 for the 1600 bpi tapes. The two versions are identical except for the tape names and file numbers which differ because of the need for more tapes at 1600 bpi. 0 A printed copy of the appropriate driver file listing (6250 or 1600) is included in the distribution. Additional copies of this listing may be printed using the LIST command in *DEDIT. The listing is ordered by component number and includes descriptive comments about each component. The revision level | "A" or "C" is printed immediately after the component number for | those components which have been included in D4.3. For these, | the tape name will be shown as 4.3Tn, whereas other components | which have not changed since D4.0, D4.1, or D4.2 will have a | tape name of the form D4Tn, D4.1Tn, or D4.2Tn. Both driver files are on the *FS tapes and on the dump/restore pack (in the files DIST:DRIVER6250 and DIST:DRIVER1600) along with the comment file (DIST:COMM), which is used by *DEDIT for the descriptive comments associated with each component. Care should be taken to never change the line numbers in a comment file since there are pointers (by line number) from the driver files into the comment file. 0 A printed copy of the appropriate driver file index (6250 or 1600) is also included. It provides an alphabetized list of the components facilitating use of the driver file listing (which is in numerical order). Additional copies of the index may be printed by copying the appropriate file to *PRINT*. The 6250 index is component 461/13 (DIST:INDEX6250 on the dump/restore pack); the 1600 index is component 461/14 (DIST:INDEX1600 on the pack). 1 4 - MTS Distribution 4.1 was the last distributed system which included support for the IBM System/360 Model 67; it was designed in such a way that it could be used on either a 360/67, System 370, or Amdahl 470. MTS distributions beginning with D4.2 support only the IBM 370 and Amdahl 470 systems. 0 | Support for IBM 2250 displays was dropped starting with | D4.2 of MTS. 0 | Components 764 thru 791 are new since D4.2; components | 779-791 are new since redistribution D4.2C. 0 | The following components were made obsolete for D4.3: 0 | XALGOLW (528/57) and ALGOLWXLIB replaced by new ALGOLW | (528) | STDTV (535/3) moved into CMDS (636) | COPY:STATDSECT (620/1) moved to COPY:MTS.MACROS (344) | FILE:DS.O (644) replaced by SYS:DSKMAN (073) | RAMP (661) | PL1LINK (670) - | The following components were assigned new component | numbers for D4.3: 0 | UC3330: changed from (603) to (787) | Online File Save: changed from (716) to (067) | File System - DASDUC: changed from (482/1) to (787/7) - Some of the components in the driver file have the letters "UNSP" in the field that indicates the person who is responsible for the component. The ID UNSP exists on the University of Michigan system to provide a common location from which unsupported programs and subroutines can be made available. UNSP software is not actively supported by the Computing Center staff. This means that there are no guarantees about its reliability, performance, or continued availability. UNSP software has received a minimal amount of testing to insure that it operates correctly for most common cases. A complete list of UNSP programs is available in component 685/3. 0 | A number of "dummy" driver file entries have been added for | components from other MTS installations that are not installed | as part of the production system at UM. These entries are | simply an aid in assigning component numbers. 1 5 - DESCRIPTION OF THE DRIVER FILE LISTING + ___________ __ ___ ______ ____ _______ - The following is a description of the driver file listing produced by the LIST and PLIST commands in *DEDIT (461/1). A printed copy of the appropriate listing (for 6250 or 1600 bpi) is included in the distribution. For each component (or subcomponent), two or three lines of output are printed, followed by any comments associated with the component. - 0 LINE 1 + ____ _ 0 Num - component number and subcomponent number (if any) + ___ R - revision level (if any) of the component or + _ subcomponent: | A or C - D4.3 Component Name - name of the component + _________ ____ Subname - name (if any) of the subcomponent + _______ Type - component type as follows: + ____ B - binary (non-360/370) object C - MTS commands D - data L - listing M - messages O - object (OC=cards, OE=link-edited, OL=library) P - printed output (PF=FORMAT, PT=TEXT360, PX=TEXTFORM) S - source code (SA=assembler, SF=FORTRAN, SG=GOM, SP=PL/I, SS=SNOBOL4, SM=assembler macros, SX=XPL, | S3=PL360, S6=Algol68, S+=PLUS, S*=SNOSTORM) U - update deck (UC=*CDUPDATE, UU=*UPDATE, UI=*IEBUPDAT, UE=$EDIT commands) W - writeup input (WF=FORMAT, WT=TEXT360, WX=TEXTFORM) G - "goodness" code (G=good, O=OK, S=shaky (has bugs), + _ B=bad (needs rewrite)) Seq ID - sequence id applied to component as it was saved + ___ __ S - save control (blank means normal, "#" means not + _ distributed, "@" means information incomplete, "=" means temporary hold, ">" means very large component) Location - file or tape from which the component was + ________ obtained. For tapes, the first parameter is the rack number, the second and third are the volume name (if labeled) and the tape id (if different from the volume name), then follow keywords for the label type, blocking format, and DSNAME (if any). File - the file number if the component was obtained from + ____ tape (optional for labeled or *FS tapes) 1 6 - LINE 2 + ____ _ 0 Tape - name of distribution tape on which the component was + ____ saved File - *FS file number on distribution tape + ____ FS Name - FS name assigned to component as it was + __ ____ saved Ver - *FS version number assigned to component as it was + ___ saved Ftype - the file type (LINE or SEQ) + _____ LRECL - the maximum record length of the component + _____ Size - the size of the component (in pages if the DevT + ____ field is PAGE, in tracks if DISK) DevT - the device type from which the component was + ____ obtained (PAGE for non-FS tapes and files, DISK for items obtained from older (before the page-formatted file system) *FS tapes) SHARE - installation code for the installation responsible + _____ for maintenance Person - the person responsible for the component at the + ______ installation given in the SHARE field Local Per - the person responsible for the component at the + _____ ___ local installation Date and Time - date and time component was saved + ____ ____ - 0 LINE 3 + ____ _ 0 Disk Name - name of the file (if any) on the dump/restore + ____ ____ pack where component is located (the save control field controls whether it is also on the *FS tapes) 1 7 - | USE OF DASDI, DUMP/RESTORE and DISKCOPY + ___ __ ______ ____________ ___ ________ 0 | Three different disks formats are currently used in MTS: | new VAMX, VAM2 and SAM. New VAMX or simply VAMX format is used | by the MTS file system. It is slightly different than the old | VAMX format which was used by several installations when they | began using 3350 type disks. Old VAMX format allowed both VAMX | and VAM2 disk addresses to coexist in the same file system. | VAM2 format is currently only required by the Paging Drum | Processor (PDP), but was the format used by the MTS file system | before the switch to VAMX format. As used by the PDP, the only | difference between VAM2 and VAMX is the volume label. SAM | format is used by HASP for its spool pack(s). 0 | Four programs are provided to initialize and restore disks. | The IBM TSS DASDI and DUMP/RESTORE programs are stand-alone | programs that may be used to initialize, dump, restore or copy | VAM2 and SAM format 2311, 2314, 3330-1 and 3330-11 disks. The | TSS DASDI and DUMP/RESTORE programs cannot use 3350 disks or | VAMX dump/restore tapes. The MTS programs FILE:DASDI (598) and | FILE:DISKCOPY (724) require a working MTS system in which to run | (they aren't stand alone programs) and may be used to | initialize, dump, restore or copy VAM2 and VAMX format 2311, | 2314, 3330-1, 3330-11, and 3350 disks (although the programs | have never been tested with 2311s, 2314s or real 3330-1s). 0 | The MTS programs FILE:DASDI and FILE:DISKCOPY are located | on the the D4.3 *FS tapes. These programs must be run in an | existing MTS system to restore the VAMX dump/restore tapes. For | old MTS installations this should be no problem, but new | installations will have to restore the D4.2 version of MTS using | the IBM TSS utilities and then use that system to restore the | D4.3 system by running FILE:DASDI and FILE:DISKCOPY (see the | instructions for new installations for details). The next | distribution of MTS will include a version of MTS that can be | IPLed directly from tape so that the use of the IBM TSS programs | will no longer be required. 0 | The MTS program FILE:DASDI will initialize a pack in either | VAM2 or VAMX format. Directions for running FILE:DASDI are | given in the MTS Operator's Manual (592) item 10075 and in | comments at the beginning of the source program. 0 | MTS file system volumes are normally labeled MTS001, | MTS002, etc. D4.0, D4.1 and D4.2 volumes must be VAM2 (V2) | format, while D4.3 packs must be VAMX (VX) format. The public | volume number for the first pack in the system must be 1 and go | up by one for each additional pack. No two packs at an | installation should have the same volume label and the same + ___ | public volume number. If you are running the DASDI program on | your production system, the SLOW option may be used to keep the | program from monopolizing the disk system. 1 8 - | The following example initializes the pack on D001 as a | VAMX pack with volume label MTS431 and public volume 1. 0 | $RUN FILE:DASDI | EXECUTION BEGINS | MTS DASDI PROGRAM (version). ENTER INPUT | D001 MTS431 VX 1 SLOW IPL | D001 CURRENTLY LABELED AS "NEW001". PLEASE CONFIRM. | OK | PAT TO BE WRITTEN ON PAGES X'009178' THRU X'00918A'. | NEXT? | $ENDFILE | EXECUTION TERMINATED - | The following example initializes the pack on D002 as a | VAM2 pack with volume label PAG001 for use as a paging volume. 0 | $RUN FILE:DASDI | EXECUTION BEGINS | MTS DASDI PROGRAM (version). ENTER INPUT | D002 PAG001 V2 PAGING SLOW | D002 CURRENTLY LABELED AS "NEW002". PLEASE CONFIRM. | OK | PAT TO BE WRITTEN ON PAGES X'009178' THRU X'00918A'. | NEXT? | $ENDFILE | EXECUTION TERMINATED - | The MTS program FILE:DISKCOPY may be used to copy VAM2 and | VAMX disk data from pack to pack as well as to and from tapes. | The program will not convert VAM2 format data to VAMX format or | vice-versa. It will copy from one disk type to another (3330 to | 3350 or 3330-11 to 3330-1 for example) as long as the "to" | volume is large enough to hold all of the data. VAM2 format | tapes produced by FILE:DISKCOPY can be restored using the IBM | TSS DUMP/RESTORE program and FILE:DISKCOPY will restore from | VAM2 format tapes produced by the IBM TSS DUMP/RESTORE program. 1 9 - | Instructions for running FILE:DISKCOPY may be found as | comments at the beginning of the source. The following example | shows a tape to disk restore: 0 | $run file:diskcopy | EXECUTION BEGINS | Enter "FROM" device type (DISK/TAPE): | tape | Enter tape device or pseudo-device names(s): | >T908 | Enter "TO" device type (DISK/TAPE): | disk | Enter device name and volume label (Dxxx MTSyyy): | D008 MTS431 | Enter options (SLOW, SWAP, IPL): | slow swap ipl | Volume copied: 29453 data pages copies, 2 relocations | Enter "FROM" device type (DISK/TAPE): | $ENDFILE | EXECUTION TERMINATED 0 | The slow option keeps the program from monopolizing the disk | system. The swap option causes the volume label on the "TO" | device to be replaced with the volume label from the "FROM" | device (in a disk to disk copy both labels would be changed). | The IPL option causes any IPL records to be copied. IPL records | are always included on a disk to tape copy, but are not normally | included on a tape to disk or disk to disk copy. These IPL | records should not be confused with the IPLAREA data used by the | IPLREADER, both types of IPL data are needed. More than one | tape device may be specified at a time, but this is not required | even when the dump/restore data spans more than one tape reel. 0 | The IBM TSS (Release 2.0) DASDI, DUMP/RESTORE, and VAM2 | UTILITIES programs are at the beginning of the dump/restore | tapes that were included with D4.0, D4.1 and D4.2. Starting | with D4.3 the dump/restore tapes are in MTS VAMX format which do | not include the TSS utility programs. Printed copies of the | writeups for TSS DASDI and TSS DUMP/RESTORE are included in the | distribution as item 10010, previously distributed with D4.0, | and therefore not included for old installations. 0 | The TSS DASDI program (stand-alone) on the dump/restore | tapes will initialize a pack in either VAM2 or SAM format; it | has been modified at UM to accept device addresses as high as | FFF. IPLing a TSS dump/restore tape once will load TSS DASDI. 0 | MTS packs should be VOLTYPE=PUBLIC and the PAT should be + ______ __ | placed on a cylinder boundary (on 3330 type disks the PATD + ______ __ _ ________ ________ | STRTADR parameter should be evenly divisible by 57) near the | middle of the pack. 1 10 - The following TSS DASDI control cards are for a 3330-1 with volume label MTS421. To DASDI a 3330-11, use TODEV=333B (instead of 3330) and STRTADR=23199 (instead of 11685). 0 JOB INITIALIZE 3330-1 AS MTS421 MSG TODEV=1052,TOADDR=53F DADEF TODEV=3330,TOADDR=440,FORMTYPE=VAM2, X VOLID=SCRATCH,VOLTYPE=PUBLIC,PUBVOLNO=1 VLD NEWVOLID=MTS421 PATD STRTADR=11685 END LASTCARD 0 If a paging disk is to be used, it should also be initialized as a VAM2 pack with VOLTYPE=PAGING and a volume | label of PAG001. No PUBVOLNO keyword is required in this case. | The Paging Drum Processor (PDP) won't accept a pack with a VAMX | label. 0 The HASP spooling pack(s) should be initialized as SAM pack(s) with volume label(s) SPOOL1, SPOOL2, etc. The following are sample control cards for a HASP DASDI: 0 JOB INITIALIZE 3330-1 AS SPOOL1 MSG TODEV=1052,TOADDR=53F DADEF TODEV=3330,TOADDR=440,FORMTYPE=SAM, X VOLID=SCRATCH,FLAGTEST=NO VLD NEWVOLID=SPOOL1 VTOCD STRTADR=1,EXTENT=1 END LASTCARD - To load TSS DUMP/RESTORE, IPL from a TSS dump/restore tape and, when the tape stops, IPL again. The following are sample control cards for restoring a TSS dump/restore tape to a 3330-1 which has been initialized with the label MTS421. To restore to a 3330-11, use TODEV=333B (instead of 3330). 0 JOB RESTORE MTS421 FROM TAPE MSG TODEV=1052,TOADDR=53F RESTORE FROMDEV=2400,FROMADDR=681,TODEV=3330, X TOADDR=440,FORMTYPE=VAM2,VOLID=MTS421, X NEWVOLID=MTS421 END 0 After restoring a dump/restore pack, you are ready to proceed with the installation of MTS. We have provided two writeups to assist in doing this, one for new installations (item 10068) and another for installations which have previously used MTS (item 10069). 1 11 - PATCHING THE SYSTEM + ________ ___ ______ - Patching shared memory: + ________ ______ _______ 0 Find out where the deck to be patched is loaded by checking a current map, by checking the file SEG2:S2MAP, or by using the LOADINFO CLS (enter the MTS command "#CLS W009:I" from a privileged user id, i.e., an id that can set PROT=OFF). 0 Use the System Status Routine (SSRTN) command 0 DISPLAY loc[+disp[+disp ...]] [n] 0 to display memory and the SSRTN command 0 MODIFY loc[+disp[+disp ...]] value[[,]value ...] 0 to change it. For example 0 DISPLAY 218500+6DBA 0 MODIFY 218500+6DBA 47F0 0 These SSRTN commands are legal from the 3270 operator's console when prefixed with a slash (/), as input to the JOBS job which may be run from any operator's console, or as input to the $SYSTEMSTATUS command when signed on using a privileged MTS user id. For a complete description of these and the other privileged SSRTN commands see the MTS Operator's Manual. 0 SDS may also be used to modify shared memory when used from a privileged id. In addition, the supervisor commands DIS and MOD may be used to display and modify routines loaded into unpaged memory (segment 0), but these commands are not legal when issued from a 3270 operator's console. 0 The IPLREADER has commands which allow a system to be patched at IPL time, see the IPLREADER description (item 10072) for more information. - Patching the System Object Deck: + ________ ___ ______ ______ _____ 0 Using RAMROD (MTS:RAMROD), CREATE a new system from the + ______ current system or GET a previously created system which has + ___ not yet been made current, but which will become the current system after the patches are made. Item 10038, which was sent with D4.1, contains a description of the use of RAMROD. Enter enough comments so that other people can tell what you've been up to. You will have been prompted for comments if you created a new system, otherwise you may use the ANNOTATE command to add comments. + ________ 0 Add REP cards to the deck(s) using the PATCH command. + _____ 1 12 - RENAME the new system with the correct version name and make it CURRENT. + _______ 0 For example: 0 # run mts:ramrod # EXECUTION BEGINS Using file "MTS:ROD" Proceed. list current UG117 created from UG057 23:06:01 08-11-77 08-11 23:00 REPLACED UMMPS TO FIX BUG IN GETSTK//SETSTK create newsys from ug117 Enter comments : ? 08-24 21:05 Just an example ? Done. patch taskstat Address Esdid Text : ? 30 01 58F0 just an example patch ? Enter comments : ? 08-24 just an example patch ? REP 000030 0158F0 example patch 21:15:25 08-24-77 W163 OK ? ok Done. rename newsys ug247 "NEWSYS" is a system. ** RENAME system "NEWSYS" as "UG247" : OK ? ok Done. current There are 3 IPL files with prefix "*IPL. " Loading system "UG247" LOAD: Resident: 1000-27D80 UMLOAD Psect: 58000 Pageable: 6C000-ACD90 End: AFFFF Contents of IPL file "*IPL.2": UL177 ENTRY=26E08 PSECT=100008 VIRTUAL=58000...ACD90 WRITTEN BY ID MTA. AT 06:24:38 07-17-77 COM 07-14 20:00 CHANGED CONFIG.CARD TO GIVE MORE SPACE TO SEGMENT 0 FOR BIG MACHINES COM 07-14 21:59 REPLACE TASKSSTAT, MINOR CHANGES. COM 07-15 13:35 NEW TABLES TO ADD MORE JOB TABLES. COM 07-17 06:20 REPLACED PDP WITH WHAT I HOPE IS THE D4.0 VERSION. ** Write system "UG247" to IPL file "*IPL.2": OK ? ok System "UG247" has been written to IPL file "*IPL.2" IPL file stacked has been pushed. System "UG247" is now the current system. "UG247" : Released. System "UG247" has been Frozen. Done. stop # EXECUTION TERMINATED 1 13 - Remember to Change the Source: + ________ __ ______ ___ _______ 0 It seems almost silly to mention this, but .... - Patching Decks Loaded by PISTLE: + ________ _____ ______ __ _______ 0 Decks loaded into shared VM by PISTLE (the post IPL system loader) can be patched in memory as described above. REP cards are added to the files from which PISTLE loads the object. It is a good idea to use PISTLE without specifying PAR=NOTEST to make sure the patched version will load. 0 PISTLE can also be used to load complete new versions of a deck into shared VM so long as all references to the module are made using a low core symbol table rather than external references that are already resolved, i.e., if the IPL option is not used to load it. PISTLE allows the automatic replacement of symbols in the low core symbol table LCSYMBOL; other low core symbol tables must be patched by hand. 1 14 - PRINTED DOCUMENTATION IN THE DISTRIBUTION + _______ _____________ __ ___ ____________ - The following lists all of the paper-copy documentation | included in D4.3. For installations which previously received | D4.0, D4.1, and D4.2 only those printed documents which have | changed since then (items 10065 and above) have been shipped | with D4.3. Items 10000 to 10029 were sent with D4.0, items | 10030 to 10046 with D4.1, items 10047 to 10064 with D4.2. Of course, all of the documents listed below are available on the *FS tapes except for those marked with an asterisk (*), which indicates that only a paper copy was shipped (no machine readable copy is available). In addition, there are many more writeups on the *FS tapes for which paper copies have not been shipped. Using the MTS editor on the driver file to match for the letters "W" or "P" in column 45 will produce a complete list of all the machine readable documentation. 0 Since some paper-copy items are not distribution components (do not appear on the *FS tapes) and hence don't have component numbers, hard-copy "item" numbers (see the list below) have been assigned. The component number for all items on tape is given in parentheses after the items in the list. The paper copy which is sent with the distribution is stamped with both numbers (if applicable). [To make them readily distinguishable, component numbers are are less than 10000; the printed documentation item numbers start with 10000 and go up.] 0 No printed copies of the volumes of the UM MTS Manual have been included with this distribution, but the TEXT360 master and print files are included on the *FS tapes. If your installation needs a printed copy of any of the MTS volumes, send a request to: 0 Elizabeth A. Sweet The University of Michigan Computing Center 1075 Beal Avenue Ann Arbor, MI 48109 USA 0 The audio tapes of the 33 system lectures given by the UM staff during 1973 have not been updated and are not included in the distribution, but are available on request. In addition, the documentation for the QUIC (584) and KWIC (583) programs has not been included, but is available on request. - Installation of MTS + ____________ __ ___ 0 | 10065. General Notes, what you are reading now. (461/10) | 10066A and 10066B. Driver file listing (LIST command output from *DEDIT). | 10067A and 10067B. Driver file index; a listing sorted by component names which serves as an 1 15 - | index for 10066. (461/13 and 461/14) | 10068. Installation instructions for New Installations. (461/8) | 10069. Installation instructions for Old Installations. (461/9) | 10070. Description of D4.3 System Object Deck | (468/7) | 10071. TABLES writeup (004/3) | 10072. Documentation for the IPLREADER and friends. | (1021/12) 10038. Documentation for the RAMROD System Maintenance Utility. (1019/9) | 10073. DECKGEN instructions (004/7) * 10010. TSS DASDI and DUMP/RESTORE instructions. | * 10074. UM Machine Configuration Chart. | * 10081A and 10081B. List of D4.3 tapes. - General + _______ 0 10012. Message Manual (555/5) - Operations + __________ 0 | 10075. MTS Operator's Manual (592) | 10076. HASP Operator's Guide (387/22) * 10015. HASP Remote 360/20 Operator's Guide * 10016. HASP Remote 360/non-20 Operator's Guide * 10017. HASP Remote 1130/1800 Operator's Guide * 10018. HASP Remote System/3 Operator's Guide * 10019. HASP 2780 Remote Workstation Operator's Guide - Software Internals + ________ _________ 0 | 10077. HASP Notes. (387/25) * 10021. SDS Storage Allocation. - How-To-Use Information + __________ ___________ 0 For systems or administrative users: * 10023. Modifying *LIBRARY. * 10024. Specifying keywords for EREP/370 (IFCEREP0) 0 For general user: | 10078A and 10078B. List of current CCMemos (461/15) | and the CCMemos themselves. * 10026. Computing Center Newsletter (v5n6 through v7n14) * 10045. Computing Center Newsletter (v7n15 through v8n9) * 10061. Computing Center Newsletter (v8n10 through v9n7) 1 16 - | * 10079. Computing Center Newsletter (v9n8 through | v10n7) | 10080. List of Computing Center Publications (461/22) * 10028. MTS Reference Summary - MTS Documentation + ___ _____________ 0 * 10063. Permission to reproduce Computing Center publications 1 17 - LISTINGS IN THE DISTRIBUTION + ________ __ ___ ____________ - Listings have been included on the *FS tapes for the most important components of the system. - Comp # Component Name 0 0042/5 MTS 0045/4 SUPERVISOR 0046/4 CONFIG 0198/4 GUINFO/CUINFO 0354/4 LLXU 0387/10 HASP 0400/6 SSCN SUBR 0464/4 PLIMIT 0513/4 DYSSUB 0531/4 CMDSTAT 0539/4 TIMNTRP 0578/4 RSF 0635/4 FSUB 0636/4 CMDS 0637/4 DSRS 0638/4 USUB 0639/4 DSRI 4000/4 GATE 1 18 - PEOPLE LIST FOR THE UNIVERSITY OF MICHIGAN COMPUTING CENTER + ______ ____ ___ ___ __________ __ ________ _________ ______ - The following is a list of UM Computing Center people whose names appear in the "person" field of the driver file listing. An asterisk (*) before a name means that the phone number is (313) 764-9595, otherwise it is (313) 764-2121. All correspondence should be addressed to: 0 The University of Michigan Computing Center 1075 Beal Avenue Ann Arbor, MI 48109 USA 0 | BLOCK Block, Frederick BODWIN Bodwin, James M. BRILL Brill, Robert C. | CASHMAN Cashman, Brian DONNELLY Donnelly, Stephen M. * DWB Boettner, Donald W. | EADIE Eadie, Gavin R. * EMERY Emery, Allan R. * ENGLE Engle, Charles F. * FLANIGAN Flanigan, Larry K. FLOWER Flower, David S. FRONCZAK Fronczak, Edward J. GOEN Goen, William GOODRICH Goodrich, Andrew C. | GREENING Greening, Daniel H YOUNG Young, Howard B. HANSEN Hansen, James H. * HARDING Harding, Leonard J. HELFFRICH Helffrich, George R. * LIFT Lift, Gail H. LUBBERS Lubbers, Clark E. MANUAL (see SALISBURY) | MERIT (see EADIE) * MTA Alexander, Michael T. MTS (see HELFFRICH) OGDEN Ogden, Jeffrey C. PICKELMAN Pickelmann, Paul * PIRKOLA Pirkola, Gary C. | * P.O. (see Salisbury) |2 | * SALISBURY Salisbury, Richard A. | SHERRY Sherry, Patrick M. | STERKEN Sterken, James J. | SWARTZ Swartz, Fred G. | * SWEET Sweet, Elizabeth A. | TIFFANY Tiffany, L. Bernard | UNSP (see PICKELMANN) VALERIO Valerio, Thomas WELTER Welter, Mark | * WSG Gerstenberger, W. Scott 1 19 - Correspondence related to the administration of the UM Computing Center should be sent to the director: 0 Dr. Aaron Finerman, Director The University of Michigan Computing Center 1075 Beal Avenue Ann Arbor, MI 48109 USA 0 Telephone (313) 764-9572 1 20 - | DISTRIBUTION 4.3 INITIAL MAILING LIST + ____________ _ _ _______ _______ ____ 0 The following is a list of persons to whom the initial | shipments of MTS Distribution 4.3 have been sent. - UBC Computing Centre 6250 bpi | ATTN: Ron Hall University of British Columbia 6356 Agricultural Road University Campus Vancouver, B. C. V6T 1W5 CANADA 0 UNE Computing Laboratory 1600 bpi ATTN: Program Librarian The University Newcastle upon Tyne NE1 7RU ENGLAND 0 UQV Computing Services 6250 bpi | ATTN: Daryl Webster The University of Alberta Edmonton, Alberta T6G 2H1 CANADA 0 WSU Computing Services Center 6250 bpi ATTN: Tony Falzon Wayne State University | 5925 Woodward Ave., Room 284 Detroit, MI 48202 0 RPI Office of Computer Services 6250 bpi ATTN: Wilson Dillaway Rensselaer Polytechnic Institute Troy, NY 12181 0 SFU Computing Centre 6250 bpi ATTN: Charlie Benet Simon Fraser University Burnaby, B. C. V5A 1S6 CANADA 0 AMD Amdahl Corporation 6250 bpi ATTN: Bill Ehrman 1250 East Arques Avenue Sunnyvale, CA 94086 0 EMB Programa Flora 1600 bpi | Attn: Stan Engilley CNPq - S.I.P. W3 NORTE QUADRA 507 BLOCO B 70.000 Brasilia D. F. BRAZIL 1 21 - | RIO CBPF/CNPq 1600 bpi | Attn: Julio L. Botelho | Av. Wenceslau Bras 71 | CEP 22.290 Rio de Janeiro - RJ | BRAZIL